Home Improvement Stack Exchange
Home Improvement Stack Exchange

Questions tagged [plastic]

146 questions
12
votes
4 answers

Is it required for effectiveness to stretch interior window film?

Thanks in advance! Please let me know if I should provide more specific information, or if this is covered somewhere else. Short version: I am using a Frost King window insulation kit on a window. Can I skip the hairdryer step and still get a good…
capet
  • 471
  • 3
  • 14
10
votes
7 answers

How can I remove melted plastic from a dryer compartment?

I have a new dryer. Someone placed a mattress cover in the dryer, the mattress cover melted and stuck to the metal plate that hot air must pass through to dry the clothes. The heat did something to the plastic and it is hard. I could chip and…
GBG
  • 291
  • 2
  • 11
9
votes
11 answers

Would wrapping a wood fence post in plastic help protect it?

I'm geting ready to install a couple new wooden privacy fence gates on the sides of our house. One of my co-workers suggested to wrap the 4"x4" with plastic stretch wrap around the 2' part that will set in the concrete. He had heard that the…
TornadoKnight
  • 171
  • 1
  • 2
  • 4
7
votes
3 answers

How to identify the type of plastic

I'm wondering if there's a practical method of recognizing what kind of plastic a something is made of. This is a recurring issue I face when trying to fix/glue/work-with plastic stuff around the house. More specifically, I was trying to fix the…
maasg
  • 275
  • 5
  • 12
6
votes
3 answers

Repair cracked plastic

I recently purchased a lawnmower that is in need of a new hood. The replacement cost for the hood is $400 so I am looking at a way to repair the old. As you can see its severely cracked. I am more concerned with structural stability than…
Steve Salowitz
  • 965
  • 4
  • 23
  • 33
6
votes
2 answers

Repair fridge door shelves

Our fridge has two white plastic shelves on the door. Both are cracked in the bottom - one just around the center, and one where almost the entire bottom has cracked along the front. I'm not entirely sure what kind of plastic they are made of -…
Grant
  • 5,589
  • 2
  • 22
  • 39
6
votes
8 answers

What is a good way to cut hard plastic so it will have a smooth finish?

I want to cut a piece of plastic peg. The peg will be visible (it is on my laptop stand), so want it to have a smooth finish. I could just use a saw, but the finish will not be good. How should I go about it? I am not sure if a file will be enough…
mythealias
  • 163
  • 1
  • 1
  • 4
5
votes
4 answers

What kind of glue is best for a black plastic kitchen appliance (ABS plastic)?

I have a built in microwave oven with a broken door open button (the hinge plastic was too thin by design). The plastic is somewhat pliable, waxy. There is no chasing arrow showing the plastic type, but it is marked ">ABS<". In the past I've…
Bryce
  • 10,586
  • 12
  • 64
  • 107
5
votes
3 answers

What glue to bond metal and plastic in cold weather?

I have a small plastic torch (flashlight) with a magnet on the back. I use it to provide light in a small metal trailer. Recently I pulled the torch off the metal wall, and the magnet came away from the torch. I've fixed this problem before, but…
Ashley
  • 359
  • 1
  • 3
  • 11
5
votes
3 answers

Why doesn't duct tape work well on cables?

In the past, I've used duct tape on cables (e.g., Power, LAN). For instance, I taped cables to a wall, I taped cables together for storing etc. The taping often failed after some time: The taping surface on the cable became covered with an extremely…
u17
  • 153
  • 1
  • 6
4
votes
4 answers

Install plastic between drywall ceilings and rafters?

We are building a new house and are getting ready to install the drywall on the ceilings. We have installed a 6 mil plastic barrier on the underside of the rafters to act as an air & moisture barrier. The barrier will be sandwiched between the…
BWDesign
  • 285
  • 5
  • 7
  • 15
4
votes
1 answer

Is it okay to use silicone sealant on plexiglass?

I've installed an air conditioner in a large horizontal sliding window, and I've used plexiglass to block off the space above the unit. I'd now like to seal the edges of the plexiglass pane to prevent air leakage. I've bought a tube of silicone…
dB'
  • 267
  • 1
  • 3
  • 10
4
votes
4 answers

How can I join PVC pipe in a food safe way?

I want to close a rectangular vertically mounted pipe with a piece of flat PVC plastic. I will use the pipe for growing herbs on the wall outside my house, so it needs to be non-toxic. I was thinking of using glue or cement for that. Does anyone…
Juila
  • 65
  • 1
  • 1
  • 4
4
votes
1 answer

How to attach plastic (vapor barrier) to the studs?

What's the best way to attach 4 mil plastic (vapor barrier) to the studs? I tried to use regular nails (sinkers 4d 1 - 3/8'') but the plastic sheet goes off the studs (through the head of the nails) any time I pull the plastic sheet a little bit.
kirill_l
  • 241
  • 1
  • 2
  • 6
4
votes
1 answer

Effective method for waterproofing a tube through a hole drilled in the side of a bucket?

How to prevent water leaking around a tube passed through the side of a bucket? The bucket is plastic approx 1mm thick wall and the tube is rubber with 6mm outside diameter. I drilled a 6mm hole and passed the tube through it, applying Araldite…
Col South
  • 151
  • 1
  • 4
1
2 3
…
9 10